AC Motors

Single Phase, TEFC

  • High-Torque design for tough applications such as farm-duty
  • 1.15 SF through 10HP
  • Oversized ball bearing
  • Manual reset overload protector installed with rubber boots/gasket
  • Rugged cast-iron frame and endbells 143T through 215T
  • Oversized and gasketed conduit box
  • Non-hygroscopic insulation system
  • Zn-Cd plated hardware
  • Dynamically balanced pressure die-cast aluminum rotor
  • Ground terminals
  • Condensation drain holes


Rolled Steel ODP EPACT

  • AC, 3 phase, 60Hz, 208-230/460V, 1.15 SF; also rated for 50Hz at 1.0 SF on nameplate (50Hz, 190/380V)
  • Usable on 200V, 60Hz
  • NEMA Design B performance; exceeds the requirements of EPACT with DOE certified
  • UL recognized Class F non-hygroscopic insulation system with HPETM - High Pulse Endurance spike resistant wire for inverter applications
  • Class B temperature rise
  • Multiple mountings for 56 and 140T; dual mountings for frame 180T~280T
  • Interchangeable F1 and F2 mounting for frame 180T~280T
  • Bi-directional rotation
  • 90 degree rotatable oversized and gasketed conduit box
  • Stainless steel nameplate
  • Accepts C-face conversion kit
  • Three year warranty


Rolled Steel ODP JM & JP EPACT

  • AC, Three phase, 60Hz, 208-230/460V, 1.15 S.F.; also rated for 50Hz at 1.0 S.F. on nameplate (50Hz, 190/380V)
  • Usable on 200V, 60Hz
  • NEMA Design B performance; exceeds the requirements of EPACT with DOE certified
  • UL recognized Class F non-hygroscopic insulation system with HPETM - High Pulse Endurance spike resistant wire for inverter applications
  • Class B temperature rise
  • Interchangeable F1 and F2 mounting for frame 180T~280T
  • Bi-directional rotation
  • 90 degree rotatable oversized and gasketed conduit box
  • Stainless steel nameplate
  • Three year warranty


High Efficiency ODP

  • HPETM - High Pulse Endurance Wire
  • Premium efficiency and high power factor
  • Corrosion resistant hardware
  • Lead lugs on 143T to 449T frame
  • Neoprene lead separator
  • F-1 and F-2 mounting interchangeability
  • C-Flange, D-Flange and P-Base kits available for 254T to 449T frame
  • Fully tested and documented per IEEE 112, Method B and NEMA MG-1
  • Class B temperature rise
  • 1.15 service factor
  • Suitable for 208V operation from 1HP to 125HP
  • Suitable for wye-delta starting from 7.5HP to 400HP (12 leads for 7.5HP to 125HP, 6 leads for 150HP to 400HP)
  • Suitable for VFD service 5:1 constant torque, 20:1 variable torque
  • 6 Leads only on 575 Volt


Oil Well Pump ODP

  • NEMA Design D, 5-8% slip
  • Cast-Iron Frame, End Brackets and Oversized Conduit Box
  • Fully guarded with Rodent Screen
  • Oversized Bearings selected for Belt-drive application
  • Grounding Terminals on Frames and Inside Conduit Box
  • Thermal Protectors embedded in Winding in each Phase
  • Stainless Steel Nameplate
  • F2 Mounting


3 Phase Fractional HP, TEFC

  • Heavy Gauge Steel Frame With Condensation Drain Holes
  • Ribbed Die-Cast Aluminum Endbells With Machined Steel Bearing Seat and Shaft Slinger
  • Large Size Double-Gasketed 90 Degree Rotatable Conduit Box
  • Oversized Vacuum De-Gassed Ball Bearing
  • High-Grade Insulated Electro-magnetic Steel Stator With Polyester Enameled Copper Wire
  • Cast-Iron C-Face Kit For Rigid Base Mount Motors
  • Cd-Zn plated Corrosive-Resistant Hardware


MAX-SE®, EPACT TEFC

  • AC, 3 phase, 60Hz, 230/460V (usable on 208V); 460V and 575V. 50Hz and other voltage under 600V are also available upon request
  • Motors are dual nameplated for 60Hz and 50Hz
  • NEMA Design B and C performance
  • MAX-SE® (type AEEANE) EPACT motors meet or exceed the requirements of EPACT 1992
  • UL recognized Class F non-hygroscopic insulation system with heavy heat resistance enameled copper wire to provide longer winding life and reliability
  • Continuous rated at 1.15 service factor


MAX-SE C-FACE®, EPACT TEFC

  • AC, 3 phase, 60Hz, 230/460V (usable on 208V); 460V and 575V. 50Hz and other voltage under 600V are also available upon request
  • Motors are dual nameplated for 60Hz and 50Hz
  • NEMA Design B and C performance
  • MAX-SE® (type AEEANE) EPACT motors meet or exceed the requirements of EPACT 1992
  • UL recognized Class F non-hygroscopic insulation system with heavy heat resistance enameled copper wire to provide longer winding life and reliability
  • Continuous rated at 1.15 service factor


MAX-HT® High Torque Crusher Motor, TEFC

  • 3 Phase, 60Hz, 460V (6 leads)
  • Premium efficiency design
  • Suitable for Across the Line Starting and Y- Delta Starting
  • NEMA Design C (Locked Rotor Torque =200% FLT; Breakdown Torque =250% FLT)
  • Class F insulation with class B rise
  • Moisture resistant copper – 2DIPs & BAKEs with Epoxy resin and 1-spray Enamel top coating for abrasion resistance
  • Thermal protection (thermistors, one per phase)
  • Squirrel-cage, Aluminum conductor with end-ring and wafer blades integrally cast rotor for all frame sizes (F#5007-5808)


MAX-E1® High Efficiency - Severe Duty, TEFC

  • HPE™ - High Pulse Endurance Wire
  • Non-hygroscopic, Class F insulation system
  • High-grade, electro-magnetic steel laminations for low core loss and high efficiency
  • All cast-iron construction including IP55 frame, end brackets, fan cover and conduit box for rigidity and excellent corrosion resistance
  • Reinforced end turn lacing
  • Neoprene lead separator
  • High performance bearings of degassed steel
  • 90° rotatable oversized cast iron conduit box for easy connection
  • Corrosion-resistant non-sparking external fan


MAX-E2® NEMA Premium Efficiency - Severe Duty, TEFC

  • Designed to meet NEMA MG-1, MG-13
  • Stock available in 460V and 575V; other voltages available upon request
  • Premium efficiency; meets or exceeds NEMA PREMIUM, EPACT ‘92 and Canadian Federal Efficiency Levels defined in CSA C390-93; Full load efficiency of all ratings is certified under the EEV Program of the CSA
  • Motors are NEMA Design “B” and "C" Torque
  • UL recognized Class F non-hygroscopic insulation system with HPE™ (High Pulse Endurance) index, heavy heat resistance enameled copper wire ensures longer winding life and reliability
  • CSA certified for Class1, Division 2, Groups B, C and D with Temperature Code T3C
  • Class B temperature rise, 80°C rise by resistance method at 1.0 SF; 90°C rise at 1.15 SF
  • 3 Leads solderless lug terminals


MAX-E2/841® NEMA Premium Efficiency - Severe Duty, TEFC

  • Designed to meet NEMA MG-1, MG-13 and IEEE 841
  • Stock available in 460V and 575V; other voltages available upon request
  • Premium efficiency; meets or exceeds the requirements of EPACT '92 and Canadian Federal Efficiency Levels defined in CSA C390-93; Full load efficiency of all ratings is certified under the EEV Program of the CSA
  • UL recognized Class F non-hygroscopic insulation system with HPE™ (High Pulse Endurance) index, heavy heat resistance enameled copper wire insures longer winding life and reliability
  • CSA certified for Class 1, Division II, Group B, C and D with Temperature Code T3C
  • Class B temperature rise, 80°C rise by resistance method at 1.0 S.F.; 90°C rise at 1.15 SF
  • 3 Leads solderless lug terminals
  • Meets GM 7E-TA specifications


MAX-E1/31® High Efficiency - Inverter Duty, TEFC

  • Insulated bearing for 324TS frames and larger to eliminate shaft currents
  • HPETM - High Pulse Endurance Wire
  • Non-hygroscopic, Inverter-grade insulation
  • High-grade, electro-magnetic steel laminations for low core loss and high efficiency
  • All cast-iron construction including frame, end brackets, fan cover and conduit box for rigidity and excellent corrosion resistance
  • Reinforced end turn lacing
  • Neoprene lead separator
  • 90° rotatable oversized cast iron conduit box for easy connection
  • Service factor 1.0 on PWM power


High Efficiency Washdown, TEFC

  • All exterior surfaces are finished with USDA approved two part epoxy paint to protect against rust, corrosion and chemical attack, and meeting the sanitary requirements
  • Double Sealed oversized bearings with Chevron SRI-2 type or equivalent high temperature/moisture resistant greases for longer bearing life
  • Contact lip seal and V-ring on both endbell and C-face protect both bearings from moisture
  • Corrosion resistant cast iron C-face for rigidity
  • Stainless steel hardware to prevent rust and corrosion
  • Drain holes in frame, endbell and C-face to allow condensation to drain
  • Threaded and fully gasketed stainless steel (2HP and below)/cast iron (3-10HP) oversized conduit box to seal out moisture
  • No. 304 stainless steel shaft and special rotor rust-resistant treatment


Closed Couple Pump JM & JP, TEFC

  • Class F insulation with Class B temperature rise
  • Cast iron frame and endbells
  • Copper windings
  • Oversized ball bearings
  • Conversion Kits CHEM-DUTY Kits
  • Continuous SF 1.15 or 1.0


TEXP HE, High Efficiency Explosion Proof, TEFC

  • HPE™ – High Pulse Endurance Wire
  • Rugged Cast-Iron Construction
  • Non-Sparking External Fan
  • Non-Sparking Brass Flingers on Both Ends
  • Oversized Cast-Iron Conduit Box
  • Non-hygroscopic Insulation System
  • Zn-Cd Plated Hardware
  • Stainless Steel Breather/Drains with Bronze Filter
  • Low Temperature Rise Operation
  • Stainless Steel Rating Nameplate and CSA Label
  • Bi-Directional Rotation


Metric, High Efficiency, TEFC/IP55

  • Premium efficiency; exceeds the federally legislated efficiency levels of EPACT 1992
  • With CE mark complying with EU Standards and Directives
  • Class F insulation with Class B temperature rise
  • Winding thermistor installed for frames D160 and larger
  • Wye-Delta start capability for 4 KW (5.5HP) and larger
  • Electrical flexibility with dual Hz, multiple volts/amps shown on nameplate
  • 230/460V at 60Hz. and 190/380V at 50Hz.
  • IP55 Protection with tapped shaft end
  • F-2 mounting
  • Oversized bearings


Global Series, Low Voltage, TEFC

  • Design Standard: NEMA MG-1; MG-13; NEMA Design B (3600 RPM) and NEMA Design C (1800, 1200 RPM)
  • Conversion Kits: C-Face, D-Flange and P-Base
  • Class F insulation
  • All cast-iron construction including conduit box, fan and fan cover (heavy gauge steel fan cover for frames 5806 and larger)
  • Copper windings
  • Oversized ball/roller bearings
  • Minimum 250% breakdown torque (except 3600 RPM)


Global Series, Low Voltage, ODP

  • Design Standard: NEMA MG-1; MG-13; NEMA Design B
  • Conversion Kits: C-Face, D-Flange, and P-Base
  • Class F insulation with Class B temperature rise
  • Cast-iron frame through 449T(S) and extra heavy gauge steel frame for frames 5007and larger
  • Cast-iron end bells and conduit boxes for all ratings
  • Copper windings
  • Oversized ball/roller bearings
  • Minimum 250% breakdown torque (except 3600 RPM)


Global Series, Medium Voltage, TEFC

  • Design Standard: NEMA MG-1; MG-13; NEMA Design B and C (1800 and 1200 RPM)
  • Conversion Kits: please contact factory
  • Class F insulation
  • All cast-iron construction (heavy gauge steel fan cover for frames 5806 and larger)
  • Copper bar rotor (for frames 5007 and larger)
  • Standard built-in winding RTDs and space heaters
  • Meets most chemical/severe duty application requirements
  • Oversized ball/roller bearings
  • Vacuum Impregnated Form Wound Coils (VPI)


Global Series, Medium Voltage, ODP/WP1

  • Design Standard: NEMA MG-1; MG-13; NEMA Design B
  • Conversion Kits: please contact factory
  • Class F insulation
  • Cast-iron frame
  • Cast-iron end bells and conduit boxes for all ratings
  • Oversized ball/roller bearings
  • Standard built-in winding RTDs and space heaters
  • Copper bar rotor (for frames 5007 and larger)
  • Vacuum Impregnated Form Wound Coils (VPI)


Premium Efficiency, Medium Voltage, Global Series, TEFC

  • AC, 3 phase
  • Available in TEFC (IP55) enclosure
  • Continuous rating with 1.15 service factor
  • All Global Series motors are designed to meet or exceed NEMA Design B torque requirements
  • Cast-Iron Construction
  • Copper Bar Rotor
  • 100 OHM Platinum Stator RTD's and 120 Volt Space Heater


  Drives and Controls

Low Voltage FM50

  • Micro AC Inverter
  • Low Cost
  • Space Saving Design
  • NEMA 4 Option for Harsh Environments
  • UL/cUL/CE Approved


Low Voltage FM100

  • Compact 1/2 to 30 HP AC Inverter
  • Low Cost
  • Keypad Mounted Potentiometer
  • Maximum Output Frequency Up To 400 Hz.
  • UL/cUL/CE Approved


Low Voltage GA7200

  • General Purpose AC Inverter
  • Low Cost V/Hz Design
  • Proven Reliability
  • UL/cUL/CE Approved
  • 230V Series 1 - 100HP
  • 460V Series 1 - 450HP


Low Voltage MA7200

  • English LCD Display /Copy Unit
  • Modbus Communication (Built-in)
  • Profibus Communication (Optional)
  • PG Feedback (Built-in)
  • PID Function
  • Simple PLC Function
  • Timer Function
  • Energy Savings Function


Low Voltage SA6

  • Compact
  • Low Horsepower
  • Reduced Voltage Starter
  • Dual Starting Mode Current Limit or Current Ramp
  • Heatsink Overtemperature Detection and Shutdown (above Size 18)
  • Run Relay Output Form C Rated 1 Amp at 240VAC
  • 1600V PIV SCR’s with MOV Surge Induction Motors
  • 3 Phase Current Feedback and Monitoring
  • 6 SCR Fully Controlled Power Circuit
  • Low Cost


Low Voltage SA7

  • Advanced Solid-State Reduced
  • Voltage Motor Starter
  • Torque Ramp for Linear Acceleration
  • Dynamic Motor Mapping Fine
  • Simple Setup for the Majority
  • Enhanced Setup for the More Demanding Applications
  • Serial Communications
  • Forward / Reverse Jogging
  • Complete Monitoring Package Eliminates Need for Add On Devices
  • Extensive Protection Features for Motor and Starter
  • Rugged Compact Design
  • Available From 7.5 HP to 1000 HP (460V)


Home
Find Supplier
Inventory
LineCard
Contact Us
Login
Set as Homepage
Add to favorites
Industrial Equipment
Search

Can't find what you're looking for. Click the following button and provide a description of the item you are looking for. It will then be added to your quote cart.

Featured Categories
AC Motors
Brakes
Drives
Generators
Magnetic Starters
Phase Converters
Seals


   The #1 Industrial Equipment Website.
Copyright © 2017 CDSoftware All Rights Reserved.
Email admin@A2ZInventory.com.
Phone: (504)273-0000
(Privacy Policy)